- Sign In
- |
- Sign Up
- |
- My Quote (0)
- |
- CART (0)
Simple and easy-to-use, this controller has a simple 'QuickStart' code to configure all the functions essential for controlling your process and is 3.78 to 3.78" (96 x 96 mm) in size. Additionally, in operator mode, every parameter has a scrolling text message describing its functions.
Simple and easy-to-use, this controller has a simple 'QuickStart' code to configure all the functions essential for controlling your process and is 3.78 to 3.78" (96 x 96 mm) in size. Additionally, in operator mode, every parameter has a scrolling text message describing its functions.
Features
Heater current monitoring
A current transformer input provides display of the heater current and a health check on the load. Heater diagnostics including full and partial open circuit, and short circuit are displayed as scrolling alarm messages as well as providing an alarm output. The front panel ammeter displays the heater current.
Setpoint programmer
Heat treatment profiles can be programmed using the 8-segment programmer. Holdback ("guaranteed soak") can be used at the beginning of each segment. A digital event output can be triggered in any segment to initiate actions within the process.
Custom text messaging
Custom messages can be created with Eurotherm iTools and downloaded to the controller to display when an event, alarm or process condition occurs. This provides the operator with good visibility of the status of the process.
Recipes
Using Eurotherm iTools, recipes can be created that may be used to change the operating parameters of the controller simply by selecting a new recipe using the HMI or digital input. This is very useful where multiple products are processed using the same controller but require different parameters to be set.
Timer
An internal timer is configurable as an interval timer, delay timer, or to provide a soft start for hot runner control.
Setpoint transmission
Sending the setpoint or other parameters from the controller to slave devices can be achieved either by using conventional analog communications or using Master Modbus communications. Master Modbus in the controller allows a broadcast of a single parameter to the network. A typical application is a setpoint being retransmitted to a number of slave controllers in a multi-zone furnace.
Modbus communication
Supports both EIA232 and 2-wire EIA485 communications using the Modbus protocol.
Configuration adaptor
Eurotherm iTools configuration to the controller can be achieved by using a USB configuration adaptor. It provides Eurotherm iTools with the ability to communicate with and configure devices without the need for any power being connected.
iTools wizard
Used to simplify the set up of the controller. The wizard guides the user through the configuration process with interactive help and graphical demonstrations of features.
Applications
Maintain high standards with this programmable controller that provides efficient, consistent production quality.
Features
Applications
Reduce equipment costs and increase efficiency
Improve quality, reduce scrap and increase profits
Adaptable, scalable and digitized
World class certification
| PV Accuracy | <0.25% |
| Display Type | High Visibility LCD three color multifunction display 4.5, 5 digit PV, 2 starburst |
| Calibration Accuracy | <±0.25% of reading ±1LSD (Note 1) |
| Supply Voltage | 24 V DC/AC 85 to 264 V AC |
| Sample Rate | 4 Hz (250 ms) |
| Input Type | TC, PT100/PT1000 RTD, mV, mA, zirconia |
| Control Types | On/Off, PID, VP |
| PV Accuracy | <0.1% low thermal drift |
| Alarm Types | Dev, Event, Heater fail, Hi, Lo, Sensor Break |
| Control Types | On/Off, PID, VP, carbon potential |
| Supply Voltage | 24 V DC/AC, 85 to 264 V AC |
| Special Features | Dual input control, recipes, text messaging |
| SP Programmer | 4 Ramp + 4 Dwell |
| SP Programmer | Up to 20 programmes of 8 segments or 10 programmes of 24 segments |
| Temperature Limits | Operating: 32 to 131°F (0 to 55°C) Storage: 14 to 158°F (-10 to 70°C) |
| Analogue IP/OP | 2 PV, 1 CT, 3 isolated DC OP |
| Panel Sealing | IP65, NEMA 12 |
| Digital Comms | BACNet, EIA-485, EtherNet/IP, Modbus RTU, Modbus TCP |
| Shock | BS EN61010 |
| Alarm Types | Hi, Lo, Dev, Sensor fault, Heater fail, Rate of Change, Event |
| Electromagnetic Compatibility (EMC) | BS EN61326 |
| IP Rating | Washdown: IP66, NEMA4x (indoor use) Standard: IP65, NEMA 12 |
| Electrical Safety | BS EN61010 Installation category II; Pollution degree 2 |
| Temperature | Operating: 0 to 55°C (32 to 131°F) Storage: -20 to 70°C (-4 to 158°F) |
| Operator Interface | Type: LCD TN with backlight Main PV display: 4 digits, green Lower display: 5 character starburst, green Status beacons: Units, outputs, alarms, active setpoint |
| Operating/Storage Humidity | 5 to 90% RH non-condensing |
| Power Requirements | 100 to 240 V AC, -15%, +10% 48 to 62 Hz, maximum 8 W 24 V AC, -15%, +10% 24 V DC, -15% +20% ±5% ripple voltage maximum 8 W |
| Atmosphere | Non-corrosive, non-explosive |
| Dimensions | 3.78 to 3.78" (96 x 96 mm) |
| Altitude | <6562' (2000 m) |
| Weight | 14.81 oz (420 g) |
| Vibration and Shock | EN 61131-2 (5 to 11.9 Hz at 7 mm peak to peak displacement, 11.9 to 150 Hz at 2 g, 0.5 octave min.) EN 60068-2-6 Test FC, vibration. EN 60068-2-27 Test Ea and guidance, shock |
| Dimension | 3.62 x 3.62" (92 x 92 mm) |
| Weight | 14.81 oz (420 g) |
| PV Accuracy | <0.25% |
| Display Type | High Visibility LCD three color multifunction display 4.5, 5 digit PV, 2 starburst |
| Calibration Accuracy | <±0.25% of reading ±1LSD (Note 1) |
| Supply Voltage | 24 V DC/AC 85 to 264 V AC |
| Sample Rate | 4 Hz (250 ms) |
| Input Type | TC, PT100/PT1000 RTD, mV, mA, zirconia |
| Control Types | On/Off, PID, VP |
| PV Accuracy | <0.1% low thermal drift |
| Alarm Types | Dev, Event, Heater fail, Hi, Lo, Sensor Break |
| Control Types | On/Off, PID, VP, carbon potential |
| Supply Voltage | 24 V DC/AC, 85 to 264 V AC |
| Special Features | Dual input control, recipes, text messaging |
| SP Programmer | 4 Ramp + 4 Dwell |
| SP Programmer | Up to 20 programmes of 8 segments or 10 programmes of 24 segments |
| Temperature Limits | Operating: 32 to 131°F (0 to 55°C) Storage: 14 to 158°F (-10 to 70°C) |
| Analogue IP/OP | 2 PV, 1 CT, 3 isolated DC OP |
| Panel Sealing | IP65, NEMA 12 |
| Digital Comms | BACNet, EIA-485, EtherNet/IP, Modbus RTU, Modbus TCP |
| Shock | BS EN61010 |
| Alarm Types | Hi, Lo, Dev, Sensor fault, Heater fail, Rate of Change, Event |
| Electromagnetic Compatibility (EMC) | BS EN61326 |
| IP Rating | Washdown: IP66, NEMA4x (indoor use) Standard: IP65, NEMA 12 |
| Electrical Safety | BS EN61010 Installation category II; Pollution degree 2 |
| Temperature | Operating: 0 to 55°C (32 to 131°F) Storage: -20 to 70°C (-4 to 158°F) |
| Operator Interface | Type: LCD TN with backlight Main PV display: 4 digits, green Lower display: 5 character starburst, green Status beacons: Units, outputs, alarms, active setpoint |
| Operating/Storage Humidity | 5 to 90% RH non-condensing |
| Power Requirements | 100 to 240 V AC, -15%, +10% 48 to 62 Hz, maximum 8 W 24 V AC, -15%, +10% 24 V DC, -15% +20% ±5% ripple voltage maximum 8 W |
| Atmosphere | Non-corrosive, non-explosive |
| Dimensions | 3.78 to 3.78" (96 x 96 mm) |
| Altitude | <6562' (2000 m) |
| Weight | 14.81 oz (420 g) |
| Vibration and Shock | EN 61131-2 (5 to 11.9 Hz at 7 mm peak to peak displacement, 11.9 to 150 Hz at 2 g, 0.5 octave min.) EN 60068-2-6 Test FC, vibration. EN 60068-2-27 Test Ea and guidance, shock |
| Dimension | 3.62 x 3.62" (92 x 92 mm) |
| Weight | 14.81 oz (420 g) |
